CAT6 Plenum cable is the standard for the sixth generation of twisted pair networking where it provides a spectacular result in the field of performance and speed. The reason behind it is, of course, the massive data transmission speed of 10 Gbps over a 100 meters wired network and the noise ratio is also reduced as compared to the previous categories with a performance frequency that can go up to 550 MHz.
Contrary to Category 6, Category 6’s augmented - the advanced version - provides does even more in the sense of noise cancellation by providing a performance frequency of up to 850 MHz. This improvement in the bandwidth, signal-to-noise ratio, and crosstalk guarantees better broadcasting in the presence of any interference in the surrounding.
About American Wire Gauge
AWG is inversely related to the wire diameter, meaning the smaller the gauge, the larger the diameter of the wire. The large diameter of the wire means less electrical resistance for the signal it carries. Copper network cables with a smaller gauge are available in longer lengths because they allow signals to travel further, by offering less resistance. Also, less resistance means it’ll generate less heat.
What AWG is in Category 6 and 6a Plenum?
Category 6 consists of 22 to 24 American Wire Gauge, meaning the width of the wire would be a bit fatter than its predecessor. Contrary to this, the width of the wire of Category 6a cable would be even faster than the predecessor of the same category, as it is a 16 to 20 American Wire Gauge. This is one of the ways you can identify between the two wires - the width. Note that both these cables use the same connector of RJ45, just like the predecessor.
What is the Plenum Jacket Type?
Just like Category 6 Standard, CAT6a Plenum Cable also comes in many variants of jacket types and the most common jacket type is Plenum. This is the reason you should know what is the difference between Plenum and non-Plenum cable so you can use them in a suitable setting.
Plenum jacket type is used in the plenum setting, which is the horizontal setting in the building and could be a viable host to heat such as air vents and raised up floors. In such places, it is recommended to use this jacket type as it has extra protection from heat and thus it protects from damage from fire - further saving from threatening causes like toxic gasses and visible smoke that can get out from the burning of the cable.
Therefore, if you are not installing the networking cable in the vertical setting then Plenum is recommended - otherwise, you might use non-Plenum cables.
 |
| Cat6 Plenum Cable |
Contrary to Category 6, Category 6’s augmented - the advanced version - provides does even more in the sense of noise cancellation by providing a performance frequency of up to 850 MHz. This improvement in the bandwidth, signal-to-noise ratio, and crosstalk guarantees better broadcasting in the presence of any interference in the surrounding.
About American Wire Gauge
AWG is inversely related to the wire diameter, meaning the smaller the gauge, the larger the diameter of the wire. The large diameter of the wire means less electrical resistance for the signal it carries. Copper network cables with a smaller gauge are available in longer lengths because they allow signals to travel further, by offering less resistance. Also, less resistance means it’ll generate less heat.
What AWG is in Category 6 and 6a Plenum?
Category 6 consists of 22 to 24 American Wire Gauge, meaning the width of the wire would be a bit fatter than its predecessor. Contrary to this, the width of the wire of Category 6a cable would be even faster than the predecessor of the same category, as it is a 16 to 20 American Wire Gauge. This is one of the ways you can identify between the two wires - the width. Note that both these cables use the same connector of RJ45, just like the predecessor.
 |
| Cat6a Plenum Cable |
Just like Category 6 Standard, CAT6a Plenum Cable also comes in many variants of jacket types and the most common jacket type is Plenum. This is the reason you should know what is the difference between Plenum and non-Plenum cable so you can use them in a suitable setting.
Plenum jacket type is used in the plenum setting, which is the horizontal setting in the building and could be a viable host to heat such as air vents and raised up floors. In such places, it is recommended to use this jacket type as it has extra protection from heat and thus it protects from damage from fire - further saving from threatening causes like toxic gasses and visible smoke that can get out from the burning of the cable.
Therefore, if you are not installing the networking cable in the vertical setting then Plenum is recommended - otherwise, you might use non-Plenum cables.
